When lead turns up in tap water, it usually comes from the plumbing rather than the treatment plant: older pipes, solder or fixtures between the water main and your glass. A filter at the point where your family drinks is one of the simplest ways to deal with that, as long as the filter you choose can show its lead results.
That evidence is the thing to shop for. A good water filter for lead names lead specifically, shows how much lead went in and how much came out, and tells you how many gallons the result covers. BOROUX proudly publishes its lead test reports for exactly that reason, so you can check every number before you buy.
What should you look for in a water filter for lead?
Plenty of filters mention lead on the box, and the ones worth buying back that up with independent results you can read. Before you buy, check these five things:
- Lead is named. A general claim such as "reduces heavy metals" is a starting point, but the results should list lead on its own line.
- The lab tested with high lead levels. A meaningful test adds far more lead than most taps carry, around 150 micrograms per liter (µg/L, the same as parts per billion), and then measures what comes out.
- Every sample stays low. Look for results at or below 5 µg/L, the limit the FDA sets for lead in bottled water, across the full run of the test rather than in a single best sample.
- The gallons are stated. Lead results are tied to a filter's capacity, so the number of gallons tested tells you when to replace the filter.
- An independent, accredited lab ran the test. A lab accredited to ISO/IEC 17025, the international quality standard for testing labs, gives you results someone outside the company can stand behind.
It's also worth checking that the filter itself is certified lead-free, which is a separate promise covered below.
Is "lead-free" the same as removing lead?
No, and a good filter keeps both promises. "Lead-free" describes the filter itself: the parts that touch your water must meet the EPA's lead-free definition, a weighted average of no more than 0.25% lead across those surfaces and 0.2% for solder and flux. The standard behind that claim is NSF/ANSI/CAN 372, a materials standard that confirms the product doesn't add lead to your water.
Reducing lead that's already in the water is answered by a performance test like the one described below. BOROUX Foundation Filters are WQA certified to NSF Standards, including NSF/ANSI/CAN 372 for lead-free materials, and the lab results show what happens to the lead in the water. The guide to NSF certification explains what each of BOROUX's certifications covers.
What this infographic shows
What each certification actually answers. Certified to and tested to are two different claims. Here is which is which.
- NSF/ANSI 42, WQA certified. Does it strain fine particles? Yes. Nominal Particulate Class I. Mechanical particle test, 0.5 to <1 µm.
- NSF/ANSI/CAN 401, WQA certified. Does it reduce microplastics? Yes, in the 0.5 to <1 µm band. Listed for 3-Gallon and 1.8-Gallon systems.
- NSF/ANSI/CAN 372, WQA certified. Does the filter add lead? No. Lead-free materials. A materials standard, not a removal claim.
Common mix-up: lead-free ≠ lead removal. 372 is about the filter's own parts. It says nothing about taking lead out of water.
Look it up: WQA product listing and boroux.com/pages/certifications. Three certifications. Every test report published.
How do carbon block filters reduce lead?
Activated carbon has an enormous internal surface area, and dissolved lead can stick to it in a process called adsorption. A carbon block packs that carbon tightly, so it can also physically catch the tiny solid specks of lead, called particulate lead, that break off from old pipes and solder. NSF describes carbon filters as working by both adsorption and filtration.
In a gravity system, gravity is simply what moves the water, and the filter element does all of the work. That's why the filter's own test results, and not the shape of the system, are what tell you whether it reduces lead.
How did BOROUX Foundation Filters perform in lead testing?
BOROUX Foundation Filters were tested for lead reduction by IAPMO R&T Lab in New Jersey, an ISO/IEC 17025 accredited laboratory. The lab ran two tests because the acidity of water changes how lead behaves, and the pass limit in both was 5 µg/L in every sample.
| Test water | Lead added (µg/L) | Average lead after filtering (µg/L) | Highest sample (µg/L) | Gallons tested |
|---|---|---|---|---|
| Slightly acidic, pH 6.5 | About 150 | 1.7 | 3 | 4,000 |
| Alkaline, pH 8.5, with particulate lead | About 150 | 1.6 | 3 | 450 |
At pH 6.5, lead dropped from about 150 µg/L to an average of 1.7 µg/L over 4,000 gallons, and individual samples showed reductions between 97.8% and 99.4%. At pH 8.5, the lab added particulate lead along with dissolved lead, and the filter brought it down to an average of 1.6 µg/L over 450 gallons. Every sample in both tests passed.
Each test used a single filter, and BOROUX's methodology note says a two-filter system can double the capacity. The two runs also used different conditions, so each result is best read on its own terms: the 4,000-gallon figure applies to slightly acidic water, while the alkaline test ran to 450 gallons per filter.
You can read both reports in full: the pH 6.5 lead report, the pH 8.5 lead report, and the complete test results page, which also covers mercury, cadmium, chromium and uranium. These are lab test results, separate from BOROUX's WQA certifications. To comply with state regulations, BOROUX Foundation Filters are only for use to reduce chlorine, chloramine, microplastics and Nominal Particulate Class I in California and Iowa, so the lead results above do not apply to products sold in those states.

What this infographic shows
Foundation Filter evidence sheet: Certified vs. tested. Every figure with its own evidence type and its own gallons.
Certified, NSF/ANSI/CAN 401: 98.9% average microplastics reduction. 0.5 to <1 µm test band, 85% required to pass. 3-Gallon and 1.8-Gallon Water Filter Systems. Below 0.5 µm: not claimed.
Tested: IAPMO R&T Lab test report, single filter.
| Contaminant | Challenge → result | Gallons |
|---|---|---|
| Lead, pH 6.5 | 150 → 1.7 µg/L | 4,000 gal |
| Lead, pH 8.5 particulate | 150 → 1.6 µg/L | 450 gal |
| Total PFAS | 2.2 → 0.02 µg/L | 400 gal |
| Chloroform (VOC surrogate) | 300 → 4.4 µg/L | 200 gal |
| Chlorine | 2 → 0.02 mg/L | 6,000 gal |
Not claimed: Nitrate, arsenic, hardness minerals, microorganisms. "This filter is not intended to filter microorganisms."
Sources: boroux.com test-report page and certifications page.
How does lead get into tap water?
Lead gets into drinking water when plumbing that contains lead corrodes. According to the EPA, the most common sources are lead pipes, faucets and fixtures, and in homes with a lead service line, the pipe that connects a house to the water main, that line is typically the most significant source. Lead pipes are more likely in older cities and in homes built before 1986, while in homes without a lead service line, the usual culprits are brass or chrome-plated brass faucets and plumbing joined with lead solder.
Corrosion is worse when water is more acidic or very low in minerals, and you can't see, taste or smell lead, so the only way to know your own levels is to test.
Is any amount of lead in water safe?
Health agencies set the bar at zero. The EPA and the CDC agree that there is no known safe level of lead in a child's blood, and the EPA has set its health goal for lead in drinking water at zero, a non-enforceable goal based on possible health risks rather than an everyday threshold.
Children are the reason the goal is so strict. The EPA explains that a dose of lead that would have little effect on an adult can have a significant effect on a child, and that infants who drink mostly formula mixed with tap water can get 40% to 60% of their lead exposure from water. For adults, the EPA links lead exposure to higher blood pressure and decreased kidney function. The practical takeaway is reassuring: lead in water is a problem you can find with a test and reduce with simple habits and the right filter.
How do you test your water for lead?
Start with your water utility, which can tell you whether your home has a lead service line and how to get your water tested. The EPA also requires every community water system to send customers an annual water quality report by July 1, and that report includes your system's lead monitoring results.
For your own tap, a certified lab gives the clearest answer, and the EPA notes that your state or local drinking water authority keeps a list of certified laboratories. If you'd like a walkthrough of an at-home lab kit, BOROUX has a guide to testing your tap water.
How can you lower lead in your water while you wait?
A few everyday habits from the EPA lower lead exposure right away, whether or not you've tested yet:
- Use cold water for drinking, cooking and making baby formula, since warm or hot water can pull more lead from pipes and fixtures.
- Flush your pipes before drinking by running the tap, taking a shower or running the dishwasher, and ask your utility how long to run the water in your area.
- Don't count on boiling, because boiling water does not remove lead.
- Clean your faucet aerators regularly, since sediment and small particles of lead can collect in the screen.
- Run only cold water through your filter, which the EPA recommends for any filter used to reduce lead.
Frequently asked questions
Do all water filters remove lead?
No. Filters are designed and tested for different contaminants, so the only way to know is to look for lead named in the product's test results or certification listing, along with the gallons it covers.
Can a gravity water filter remove lead?
Yes, when the filter element is designed and tested for it. BOROUX Foundation Filters reduced lead to an average of 1.7 µg/L over 4,000 gallons at pH 6.5 and 1.6 µg/L over 450 gallons at pH 8.5 in independent lab testing.
Does boiling water remove lead?
No. The EPA is clear that boiling does not remove lead, so a filter tested for lead, cold water and flushing are the steps that help.
Is it safe to shower in water with lead?
The EPA says bathing and showering should be safe for adults and children, even if the water contains lead above the EPA's action level, because human skin doesn't absorb lead in water.
Is NSF/ANSI/CAN 372 the same as lead removal?
No. NSF/ANSI/CAN 372 confirms that the filter's water-contact parts are lead-free, so the filter doesn't add lead. Lead removal is shown by performance testing, which is why BOROUX publishes its lead test reports alongside its certification.
How often should you replace a water filter used for lead?
Replace it at or before the number of gallons it was tested to, and sooner if the flow slows noticeably. For BOROUX Foundation Filters, the lead results cover 4,000 gallons per filter at pH 6.5 and 450 gallons per filter at pH 8.5.
Choose a filter you can check
If lead is the reason you're shopping, choose a filter that shows you the numbers. The BOROUX 3-Gallon Water Filter System and the 1.8-Gallon Water Filter System both come with BOROUX Foundation Filters, which are WQA certified to NSF Standards for lead-free materials, and the full lead test reports are published for you to read before you buy. For a closer look at the test data, see Does a Water Filter Remove Lead?